Home :: Mounts/Risers 1 Piece

Mounts/Risers 1 Piece


Fixed 1 Piece 1" Mounts
1 products

Fixed 1 Piece Drooper Mounts
2 products

Fixed 1 Piece Risers

Adjustable 1 Piece 1" Mounts
1 products

Beeman 5036 1 Piece Mount

Fixed 1 Piece High 1" (Rings) 11mm (Base) Mount

For the shooter who wants a scope mount with absolute maximum clamping ability and the extra height for the larger scopes, this is it! The one-piece construction affords the greatest area of grip, and the four screws along the side give even clamping pressure for a sure hold.. Made from the finest materials, the mount has an attractive matte finish. For use with all one inch scope tubes and objectives up to 56mm.

$67.00
Quantity
Beeman 5039 1 Piece Mount

Adjustable 1 Piece High 1 Inch (Rings) 11mm (Base) Mount

This one piece double screw mount is adjustable for windage and elevation. It's suitable for all spring guns or semi auto rimfire rifles as well as some pre-charged pneumatic air rifles.  The maximum amount of adjustment is 2mm from one end of the mount to the other.  This applies to the windage and elevation and  60mm diameter objective lens will clear on most rifles.  Removable arrestor pin included.

Also sold as the Sportmatch APO55 1 piece adjustable mount.

$74.99
Quantity
Extended Impact Trigger Guard

Extended Impact Trigger Guard Gen 2 guards with integrated T-slot and curved rear.

New features:
Curved rear for a more flush fit with the pistol grip
T-slot that can receive any T-rail parts
Thicker extension for less flex and more stability
Small cutout under the air bottle

The Easy Access Trigger Guard Gen 2 is designed to allow better access to the foster fitting, making it easier to connect and disconnect when refilling your FX Impact.

Designed to place the bi-pod further towards the front to significantly increase the stability of your shot.
Machined from 6061 T6 aluminum and anodized it is designed to be strong, light weight and handle corrosive environments. This guard is made a bit lower than the OEM part so that the bottom to the guard covers the fill port on the gun. This protects the fill port and allows a cap to fit flush with the bottom of the guard. The cap is held on by a strong magnet.

In addition, the back end of the trigger guard now lines up with the pistol grip unlike the OEM part. Includes one guard and one cap. Kraford & Lypt is in the business of building quality parts you can trust. They want their products to make your life easier and your shooting experience more accurate. That is why they back every FX Impact Easy Access Trigger Guard, long and short, with a life time warranty.

$125.00
Quantity
FX-Wildcat-Weaver-Rail

FX Wildcat Weaver Mounting Rail


Use this OEM weaver rail to replace the standard 11mm rail on your FX Wildcat. Simple to install this rail provides you with the standard weaver rail used by many scope, mount and red dot brands.

$119.99
$124.95 (save 4 %)
Quantity
RWS 230-0596 1 Piece Mount 1"

Fixed 1 Piece High 1" (Rings) 11mm (Base) Drooper Mount

These mounts are designed specifically to be used with RWS rifles. RWS rifles are known to have barrel droop and these mounts were designed to counteract the droop. The mounts are fixed so there are no small screws to loosen up over time and there is .025" of droop compensation built in. The mounts also feature 2 stop pins that lower into the 2 indentations on RWS scope rails.  The mount is available with 1" rings or 30mm rings.

$35.00
Quantity
RWS 230-0597 1 Piece Mount 30mm

Fixed 1 Piece High 30mm (Rings) 11mm (Base) Drooper Mount

These mounts are designed specifically to be used with RWS rifles. RWS rifles are known to have barrel droop and these mounts were designed to counteract the droop. The scopes are fixed so there are no small screws to loosen up over time and there is .025" of droop compensation built in. The mounts also feature 2 stop pins that lower into the 2 indentations on RWS scope rails. The mount is available with 1" rings or 30mm rings.

$35.00
Quantity

Bestsellers

Beeman 5039 1 Piece Mount

Adjustable 1 Piece High 1 Inch (Rings) 11mm (Base) Mount

This one piece double screw mount is adjustable for windage and elevation. It's suitable for all spring guns or semi auto rimfire rifles as well as some pre-charged pneumatic air rifles.  The maximum amount of adjustment is 2mm from one end of the mount to the other.  This applies to the windage and elevation and  60mm diameter objective lens will clear on most rifles.  Removable arrestor pin included.

Also sold as the Sportmatch APO55 1 piece adjustable mount.

$74.99
Quantity
RWS 230-0596 1 Piece Mount 1"

Fixed 1 Piece High 1" (Rings) 11mm (Base) Drooper Mount

These mounts are designed specifically to be used with RWS rifles. RWS rifles are known to have barrel droop and these mounts were designed to counteract the droop. The mounts are fixed so there are no small screws to loosen up over time and there is .025" of droop compensation built in. The mounts also feature 2 stop pins that lower into the 2 indentations on RWS scope rails.  The mount is available with 1" rings or 30mm rings.

$35.00
Quantity
RWS 230-0597 1 Piece Mount 30mm

Fixed 1 Piece High 30mm (Rings) 11mm (Base) Drooper Mount

These mounts are designed specifically to be used with RWS rifles. RWS rifles are known to have barrel droop and these mounts were designed to counteract the droop. The scopes are fixed so there are no small screws to loosen up over time and there is .025" of droop compensation built in. The mounts also feature 2 stop pins that lower into the 2 indentations on RWS scope rails. The mount is available with 1" rings or 30mm rings.

$35.00
Quantity
Beeman 5036 1 Piece Mount

Fixed 1 Piece High 1" (Rings) 11mm (Base) Mount

For the shooter who wants a scope mount with absolute maximum clamping ability and the extra height for the larger scopes, this is it! The one-piece construction affords the greatest area of grip, and the four screws along the side give even clamping pressure for a sure hold.. Made from the finest materials, the mount has an attractive matte finish. For use with all one inch scope tubes and objectives up to 56mm.

$67.00
Quantity
FX-Wildcat-Weaver-Rail

FX Wildcat Weaver Mounting Rail


Use this OEM weaver rail to replace the standard 11mm rail on your FX Wildcat. Simple to install this rail provides you with the standard weaver rail used by many scope, mount and red dot brands.

$119.99
$124.95 (save 4 %)
Quantity
Extended Impact Trigger Guard

Extended Impact Trigger Guard Gen 2 guards with integrated T-slot and curved rear.

New features:
Curved rear for a more flush fit with the pistol grip
T-slot that can receive any T-rail parts
Thicker extension for less flex and more stability
Small cutout under the air bottle

The Easy Access Trigger Guard Gen 2 is designed to allow better access to the foster fitting, making it easier to connect and disconnect when refilling your FX Impact.

Designed to place the bi-pod further towards the front to significantly increase the stability of your shot.
Machined from 6061 T6 aluminum and anodized it is designed to be strong, light weight and handle corrosive environments. This guard is made a bit lower than the OEM part so that the bottom to the guard covers the fill port on the gun. This protects the fill port and allows a cap to fit flush with the bottom of the guard. The cap is held on by a strong magnet.

In addition, the back end of the trigger guard now lines up with the pistol grip unlike the OEM part. Includes one guard and one cap. Kraford & Lypt is in the business of building quality parts you can trust. They want their products to make your life easier and your shooting experience more accurate. That is why they back every FX Impact Easy Access Trigger Guard, long and short, with a life time warranty.

$125.00
Quantity